Autonomous cleaning, redefined at altitude.
The TDS X4 combines aerospace-grade engineering, dual RTK precision and a modular spraying system — turning facade maintenance into a forty-minute autonomous mission, with no scaffolding.
We build the machines that erase risk — scaffolding, harnesses, hours lost to weather. The TDS X4 is a silent revolution in height maintenance: precise, repeatable and rarely efficient.
RTK guidance down to the centimetre, pass after pass.
Six times the productivity of a traditional crew, at 70% lower cost.
Operators on the ground. Zero work at height.
Four pillars, one mission.
Every TDS X4 flight combines intelligent routing, satellite precision and ground-level safety for a flawless result, mission after mission.
01Full coverage
Complete facade cleaning with no missed zones thanks to programmed trajectories.
02Autonomous flight
The drone automatically follows the programmed mission to ensure regular, consistent cleaning.
03Stable positioning
The GNSS RTK system maintains high positioning accuracy even on high-rise facades.
04Operator safety
The operator stays on the ground throughout the mission, limiting risk and height interventions.
The TDS X4. An industrial platform built for high and low pressure.
Six advantages, one obvious choice.
A design driven by operational efficiency: every TDS X4 parameter has been optimised to deliver industrial results, safely.
Automatic trajectory
Intelligent route planning for methodical, efficient cleaning.
RTK navigation
GNSS RTK for precise, stable positioning at every moment.
Smart coverage
Optimised surface overlap for a perfect, uniform result.
Remote piloting
Remote control and supervision for maximum safety and flexibility.
High precision
Centimetre precision for consistent cleaning without quality loss.
Professional safety
Zero work at height and reduced risk for operators.
One drone. Six modules. Zero compromise.
Each module is swapped in under thirty seconds. The drone stays operational; the ground crew changes chemistry according to the mission.
Foam
Dense foam application for deep cleaning.
Soft Wash
Low-pressure detergent for delicate surfaces.
High pressure
Up to 150 bar for the toughest deposits.
Rinse
Clear-water finishing pass, streak-free.
Bio-detergent
Eco-certified formula for sensitive environments.
Glass
Specially designed for glass surfaces.
Cover every cm² with precision.
The TDS X4 uses intelligent route planning to clean facades methodically, efficiently and without manual work at height.
Intelligent planning
Programmed vertical and horizontal trajectories for repeatable missions.
Automatic cleaning
The drone follows a predefined path — no manual piloting required.
RTK precision
Centimetre positioning for homogeneous coverage on every zone.
Remote supervision
The operator supervises the entire mission from the ground, safely.
Wherever the surface is high, vertical or hard to reach.
Planning a roof cleaning project? Read our complete guide covering method, safety and budget. Read the drone roof cleaning guide
Roofs
Complete roof cleaning without ladders or lifelines.
Industrial cladding
Ribbed metal panels restored in a single pass.
Silos & installations
Intensive cleaning of silos and industrial installations.
Solar panels
Maximise output of large-scale photovoltaic fields.
Glass facades
Impeccable results on towers and commercial buildings.
Hotels & monuments
Discreet maintenance of high-visibility facades.
Precision at every level.
Dual GNSS RTK
Centimetre positioning with redundant receivers for constant precision in any environment.
Intelligent flight controller
Industrial autopilot with obstacle avoidance, return-to-home and safety protocols.
Carbon structure
Aerospace composites optimised for unmatched payload-to-weight ratio.
Brushless motors
High-torque, thermally regulated motorisation designed for sustained heavy-lift flight.
AI planning
Define the zone once — the software generates efficient, repeatable trajectories.
Obstacle avoidance
Multi-directional sensor network for operating in complex architectural environments.
Traditional cleaning versus TDS X4.
A team of engineers dedicated to height maintenance.
TitanDrone-Solutions designs and distributes the TDS X4 in Europe, a professional hexacopter drone for autonomous cleaning of facades, roofs, solar panels, industrial silos and cladding.
Our approach combines aerospace, robotics and surface chemistry to provide a reliable, repeatable industrial tool that is immediately productive on site.
Your questions, our answers.
What is the TDS X4 autonomy?
Up to 40 minutes in typical cleaning conditions — enough to cover about 1000 m² per session.
What is RTK and why does it matter?
RTK (Real-Time Kinematic) provides centimetre GPS precision. The drone follows exactly the same path every pass, ensuring homogeneous cleaning.
Can the TDS X4 clean solar panels?
Yes. The Soft Wash module delivers a gentle low-pressure rinse designed for photovoltaic fields, with no risk to the surface.
Is a certified pilot required?
Two ground operators are enough. TDS provides certifying training as part of the delivery programme, compliant with European regulation.
Is the drone certified for professional use?
The TDS X4 is CE certified and built to European industrial standards.
What is the delivery lead time?
Standard configurations are delivered within 6 to 8 weeks after order confirmation.
Roof cleaning
Soft wash method, safety without scaffolding, output up to 1000 m²/h, budget and use cases: our complete guide walks through every stage of a drone roof-cleaning job.
Ready to transform your height maintenance?
Request a TDS X4 demonstration or receive a detailed technical sheet. Our team replies within 24 hours.
Your data is only used to respond to your request.